Proxim Harmony 802.11a Uživatelská příručka

HarmonyHarmony Power SystemUser's Guide

About the Harmony Power System 10Typical Network ConfigurationFigures 1 and 2 illustrate how a Harmony Power System fits into your existing networking

About the Harmony Power System 11Keep in mind the following considerations when connecting Access Points to the Power System:• The maximum UTP (Unshie

About the Harmony Power System 12Automatic Device DetectionWhen a device is connected to one of the Harmony Power System’s Output Ports, the Power Sys

About the Harmony Power System 13Description of Front Panel Connectors and LEDsFigure 3 shows the front panel of the Harmony Power System.Figure 3: Po

About the Harmony Power System 14Channel Status LEDsEach pair of Input and Output ports has one LED indicator that provides information about the chan

About the Harmony Power System 15Description of Rear PanelFigure 4 shows the back panel of the Harmony Power System.Figure 4: Power System Rear PanelP

16Chapter 3 Installing the Harmony Power SystemFollow these steps to install the Harmony Power System:1. Choose a Suitable Installation Location.2. Ra

Installing the Harmony Power System 17Step 2: Rack Mount the Harmony Power System (Optional)The Harmony Power System is 1U (Unit) high and fits in mos

Installing the Harmony Power System 18Step 3: Power Up the Harmony Power SystemFollow these steps to power up the Harmony Power System:1. Plug the pow

Installing the Harmony Power System 19Step 4: Confirm That the Harmony Power System Is OperationalMonitor the LEDs on the front panel of the Harmony P

Copyright© 2002 Proxim Corporation, Sunnyvale, CA. All rights reserved. This user’s guide is copyrighted with all rights reserved. No part of this

Installing the Harmony Power System 20Step 5: Attach the Ethernet CablesThe Harmony Power System includes six Input Ports (the bottom row of RJ-45 con

21Appendix ASafety InformationYou must read the following safety information before installing or uninstalling the Harmony Power System.Important Safe

22• This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 950. The conditions are only maintained if the equipment to

23Appendix BTechnical SpecificationsThe following technical specification is for reference purposes only. Actual product’s performance and compliance

24Immunity ...EN 61000-4-2, EN 61000-4-4, EN 61000-4-6, EN 61000-4-11Output Power ...

25Appendix CRJ-45 Connector Pin-outsAll of the ports on the front of the Harmony Power System are configured as “route through” for all 4 data wires (

26RJ-45 Output Plug (per channel) — Access Point SideUse two standard straight-through Ethernet cables that include all 8 wires (4 pairs) to connect t

27Appendix DTroubleshootingIf the Harmony Power System’s LEDs indicate a problem, refer to the following table, which contains a list of problems and

28I've connected one Ethernet cable to the network switch and an Input Port and a second Ethernet cable to a Harmony OpenAir Access Point and the

29 Technical Support and TrainingIf you’re having a problem using the Harmony Power System, gather the following information and contact Proxim Techni

3Table of Co n ten tsChapter 1 - Introduction ... 4The Harmony Family

30IndexAAP Power Over LAN Module. See Harmony Access Point Power Over LAN ModuleAutomatic Device Detection...

31NNumber of APs Supported by Power System ... 8OOutput Port ...

4Chapter 1IntroductionCongratulations on your purchase of the Harmony Power System, a member of Proxim’s Harmony family of wireless networking product

Introduction 5The Harmony FamilyThe Harmony Power System is a member of a product family that provides a complete wireless networking solution.•The Ha

Introduction 6The Product PackageEach Harmony Power System comes with the following:• One Harmony Power System• One AC power cord• One rack mounting a

7Chapter 2About the Harmony Power SystemThe Harmony Power System is an efficient and simple way to provide operating power to Harmony Access Points.

About the Harmony Power System 8Remote Power Feeding of Harmony Access PointsThe Harmony Power System supplies DC power to Harmony Access Points (APs)

About the Harmony Power System 9AP Power Over LAN ModuleThe Harmony OpenAir Access Point must be attached to a Harmony AP Power Over LAN Module Model